FAAC Gate Installation Nationwide

FAAC Gate Installation in Fort Worth: What to Know First

FAAC gate installation in Fort Worth typically runs $1,800 to $6,500 for a complete system, depending on whether you’re outfitting a single swing gate, a double gate, or a sliding driveway gate. We complete most FAAC installations in one to two days once the site is measured and the equipment is on hand, and every quote is settled in writing before we turn the first bolt. As an independent FAAC service provider, we install and service the full range of FAAC residential operators: the 400, 402, 412, 415, 770, and the C720/C721 slide operators that show up on heavier estate gates across Tarrant County. If you own a FAAC opener or you’re considering one for a new gate, call (817) 562-7979 and we’ll talk through your driveway before anyone schedules a visit.

Call (817) 562-7979

This page is written for the homeowner who already has a FAAC unit on the driveway, or who has been told FAAC is the right choice and wants to know what that actually means in Fort Worth soil, heat, and traffic. You’ll find what fails, what it costs, how we work, and why we treat every FAAC job like the gate will outlast us both.

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid operator. But every brand has its habits, and after four decades of opening them up, we know exactly where FAAC units complain in North Texas. Here are the five failure modes we see most often on FAAC gate installation and repair calls across Fort Worth:

• Capacitor failure on the 400 and 402 series. The 400-series swing operators run on a single-phase motor that depends on a start capacitor. In a Fort Worth summer, attic heat and direct sun on a steel operator box push the capacitor past its rating. The gate hums, the arm twitches, and the board throws a fault code the homeowner doesn’t see. We replace the capacitor with a higher-temperature-rated unit and verify the start winding on every 400-series install, because a weak capacitor left in place will take the board down with it eventually.
• Limit switch drift on the slide operators, especially the C720 and C721. FAAC slide operators use magnetic limit switches that ride along a track inside the housing. After a few years of Fort Worth clay soil shifting under the concrete pad, the gate’s end-of-travel position moves half an inch. The operator doesn’t know it. So the gate starts slamming into the end stop or stopping short of the receiver. On install day we set the limits with the gate loaded, then run it thirty cycles to settle the chain before locking the positions. Most contractors skip the settle run. That’s why most FAAC slide gates in Fort Worth need their limits reset within two years.
• Oil leaks from the hydraulic units on the 415 and 770 series. The hydraulic FAAC operators are genuinely smooth, but the reservoir seals dry out in our low-humidity winters. A slow weep around the filler cap or the ram seal doesn’t look like much until the pump runs hot and the gate slows to a crawl midway through its arc. We check the fluid level and seal condition on every hydraulic FAAC install, and we set the bypass pressure to the gate’s actual weight rather than leaving the factory setting, which is usually too high for a residential gate and shortens the pump’s life.
• Photo eye and safety edge wiring that’s been spliced badly. This isn’t FAAC’s fault. It’s the installer’s. FAAC control boards are sensitive to resistance changes across the safety circuit. A corroded wire nut or a cheap splice under the driveway will read as a fault intermittently, and the gate will refuse to close or reverse without reason. When we install or repair a FAAC operator in Fort Worth, every safety connection gets a sealed, heat-shrunk splice, and the eyes get aligned on a bracket that won’t flex in wind. The number of FAAC service calls we take that turn out to be a bad splice from a previous installation would surprise you.
• Battery backup issues on units with the E024U or E124 board. FAAC’s battery option is a selling point until the battery is three years old and the board won’t charge it properly. The gate works fine on line power, then the power flickers during a spring storm and the gate goes dead. On installations where the homeowner wants battery backup, we test the charging circuit before we hang the operator, and we install a battery with enough reserve to run the gate through a full day of normal use. Fort Worth thunderstorms don’t wait for the battery warning light.

The common thread in all of these: most FAAC failures aren’t the motor. They’re the details around the motor. If the details are right on day one, the operator runs for a decade. Victor Salinas grew up watching his grandfather weld ornamental iron in Polytechnic Heights, and he learned early that the part you can’t see is the part that decides whether the gate works. We build installs so the part you can’t see is right.

Our FAAC Gate Installation Process

Every FAAC gate installation in Fort Worth follows the same sequence. No shortcuts, no surprises.

1. 1
   Measure and site visit. We come out, measure the gate leaf or leaves, check the hinge posts and the gate’s weight, and look at how the driveway is graded. A gate that’s out of square or dragging on one hinge will eat a new FAAC operator in months. We tell you honestly whether the gate itself needs work before the operator goes on.
2. 2
   Written quote. The price is settled before any work starts. That includes the operator, mounting hardware, any fabrication or gate repair, safety devices, and the control wiring. No allowances, no “we’ll see how it goes.” The number we write down is the number on the invoice.
3. 3
   Parts decision. We use OEM FAAC parts whenever the job calls for them, especially boards and motors where the manufacturer’s component is the only part that carries the warranty properly. For hardware items like brackets, battery boxes, and photo eye housings, we’ll use quality aftermarket parts where they’re equal or better and where they save you real money. We’ll tell you which is which and why before we order anything.
4. 4
   Installation. The operator, arm or chain, safety eyes, keypad or receiver if you’re adding one, and the power run if it’s needed. Mounting plates get through-bolted, not lag-screwed into the post. The operator gets set to the actual weight and travel of your gate, not the factory default.
5. 5
   Cycle test and handover. We run the gate through thirty full cycles at minimum, check the safety reverse in both directions, set the close delay, and leave you with the remotes programmed and the manual release demonstrated. You’ll know how to open the gate when the power’s out.
6. 6
   Written Done Right Promise. Every FAAC installation gets the 90-Day Done Right Promise in writing. If anything isn’t right, we come back and make it right. No paperwork, no arguing.

What FAAC Gate Installation Costs in Fort Worth

Here’s an honest look at what FAAC work runs in the Fort Worth market. These are the numbers we quote, and they reflect what we see across Tarrant County driveways:

• Single swing gate with FAAC 400 series operator: $1,800 to $3,200, installed, including two remotes and safety photo eyes.
• Double swing gate with FAAC 402 or 415 hydraulic operators: $3,500 to $6,500, installed, depending on gate weight and whether the posts need reinforcement.
• Sliding driveway gate with FAAC C720/C721 operator: $3,900 to $6,500, installed, including the track or v-groove work and chain or rack depending on the gate.
• Replacing an existing opener with a new FAAC unit on an existing gate: $1,400 to $2,800, depending on the operator and how much of the old wiring and mounting is salvageable.

What moves the price: gate weight and condition, post integrity, whether we’re running new power from the house, and whether you want battery backup or a keypad added. Every estimate is free, and every estimate is the final number. Call (817) 562-7979 and we’ll give you a real price for your specific gate, not a range that shifts when the crew arrives.

Why Fort Worth Homeowners Call Ironworks Gate Co. for FAAC Work

We are a gate company. Not a fence company that also hangs openers, not a generalist handyman working out of a pickup. Gates are what we do, and FAAC is one of nine automation brands we carry the training and the parts knowledge for. If you ever decide to switch brands down the road, we service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing as well. But for FAAC specifically, we know the boards, we know the capacitors, we know the limit switches, and we know what happens to all of it when a Fort Worth August sits on it for six weeks straight.

Every job is backed by the 90-Day Done Right Promise in writing. A live person answers the phone 24 hours a day, seven days a week, not a voicemail tree. Our technicians are background-checked and uniformed, and they work on your property the way they would work on their own mother’s driveway. We’ve been in business since 1984, which means we’ve seen operators come and go, brands rise and fade, and gates outlast the contractors who hung them. We plan to be here for the next forty years, standing behind the work.

If the gate doesn’t open when it should and close when it should, nothing else about it matters much. That’s the standard every FAAC job starts from.

Frequently Asked Questions