FAAC Gate Repair Nationwide

FAAC Gate Repair in Fort Worth: What to Know First

FAAC gate repair in Fort Worth typically runs between $220 and $480 for most motor and control board failures, with hinge and weld work landing in the $180-$340 range. We complete most FAAC repairs in a single visit, and every job carries our written 90-Day Done Right Promise. If your FAAC opener is acting up, call (817) 562-7979 and a live person answers, day or night.

Call (817) 562-7979

This page is written for Fort Worth homeowners with a FAAC swing or slide gate that has stopped behaving. Maybe the gate groans halfway through its arc. Maybe the remote works only from ten feet away. Maybe the motor hums but the gate doesn’t move. Whatever it’s doing, you want to know what’s wrong, what it costs, and whether it’s worth fixing. That’s what we cover here. As an independent FAAC service provider, we’re not tied to the manufacturer’s parts network or their pricing. We’re tied to getting your gate working again.

How FAAC Products Fail - and How We Fix Them

FAAC builds durable automation, which is why you’ll find twenty-year-old FAAC operators still bolted to gates across Fort Worth. But age, heat, and poor past service take their toll. These are the failures we see most often on FAAC equipment in this area:

• Worn capacitor on 400 and 402 series operators. The symptom is a gate that hums or shudders but won’t start moving. The motor is fine; the start capacitor has dried out from years of Dallas-Fort Worth summer heat. We replace the capacitor with a NEMA-rated equivalent and the gate usually moves normally that same visit.
• Failed limit-switch assembly on FAAC 750 and 844 models. These slides and heavy swing gates rely on microswitches that physically wear down. The gate begins stopping two feet short of the post, or it over-travels and buries itself in the shrubbery. We adjust, rebuild, or replace the switch assembly depending on what the contacts look like.
• Burned relay on FAAC E124 control boards. A lightning strike or a power surge takes out the relay, and suddenly the gate only opens from one control and not the other, or the open command trips the board. The board often doesn’t need replacing. We desolder and replace the relay where that’s safe, which costs a fraction of a new board.
• Stripped manual-release mechanism on FAAC C721 and S418 operators. A previous repair overtightened the release, or someone forced it during a power outage. Now the release won’t engage, so the gate can’t be operated by hand if the power fails. We repair the release and, as a habit, test it twice before we leave the driveway.
• Worn drive belt or reduction gear on FAAC 770 and B680 series. The gate starts rough and gets worse, especially in cold weather, or you hear a constant whine from under the cover. That’s the drive train asking for help. We replace belts and refurbish reduction gears with proper tolerances, then re-time the gate to its stops.

Our FAAC Gate Repair Process

Here’s exactly what happens when you call us about a FAAC gate problem in Fort Worth:

1. 1
   You call. A live person answers, 24/7. We ask what the gate is doing, what brand and roughly how old, and whether it’s your only way into the property. Then we schedule the visit.
2. 2
   We arrive and we look. Victor Salinas or one of our senior techs opens the operator cover and inspects both the mechanical end and the electrical end. We don’t guess. We meter the circuit, check the capacitor, and physically test the hinges and post anchors.
3. 3
   We quote the repair. Before any bolt is turned, you know the price. Not an estimate, a price. If we find additional problems after we’re inside the operator, we call you before doing a thing. No surprises on the bill, ever.
4. 4
   Parts decision, made with you. Where FAAC OEM parts are still available and make sense, we use them. Where OEM is backordered for weeks or costs three times as much for no better reliability, we offer a quality aftermarket equivalent and tell you the trade-off straight.
5. 5
   We fix it and test it. The repair is made, then the gate cycles ten times minimum. We check the force settings, the reverse function, the travel limits. If your FAAC gate has photo eyes or an edge sensor, we test those too.
6. 6
   You get it in writing. Every job leaves with our 90-Day Done Right Promise. If something isn’t right, we come back and make it right. No paperwork, no arguing, no exceptions.

What FAAC Gate Repair Costs in Fort Worth

Here’s what FAAC owners in Fort Worth should expect, based on the jobs we’ve done across Tarrant County in the past year:

• Start capacitor replacement: $140-$210
• Limit switch adjust or rebuild: $160-$240
• Relay replacement on control board: $180-$260
• Full operator swap (FAAC 400/402 class): $1,200-$1,900 installed
• Hinge, post, or weld repair: $180-$340
• Complete diagnostics visit (credited to repair if we do the work): $89

What moves the price? Access to the board, the age of the unit, whether OEM or aftermarket parts are appropriate, and what we find when the cover comes off. We stand behind every price we quote. And here’s the important part: the price is quoted and agreed before any work starts. If you’ve been burned by an invoice bigger than the estimate, that won’t happen on our watch. Call (817) 562-7979 for a free estimate on FAAC repair in Fort Worth.

Why Fort Worth Homeowners Call Ironworks Gate Co. for FAAC Work

We’ve been serving Fort Worth since 1984, and we plan to be doing it for another forty years. That’s the difference between a handyman who’ll take a look at your FAAC opener and a team that knows exactly which capacitor belongs in a 402 series and which week the new boards ship. Victor Salinas grew up in Polytechnic Heights, where his grandfather welded ornamental ironwork out of a shop behind the house. The standard hasn’t dropped since.

Every repair carries our 90-Day Done Right Promise in writing. A live person answers the phone, every hour, every day. And if your FAAC should ever need to be replaced entirely, our techs are trained on nine brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. That breadth matters when it’s time to make a smart swap instead of a sentimental repair. In Natomas and across Fort Worth, same logic applies: the correct fix is the one made on the first visit.

FAQs

Contact Ironworks Gate Co. for FAAC Repair in Fort Worth

If your FAAC gate is acting up in Fort Worth, don’t nurse it through another week. Call (817) 562-7979 and a live person will pick up, listen, and get you scheduled. You get a free estimate, a fair price settled before the work starts, and the 90-Day Done Right Promise in writing. Done right, and backed in writing. Always.

Written by Victor Salinas, Owner, Ironworks Gate Co., serving Fort Worth and nearby areas.