Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The Fort Worth Owner’s Guide

We stock and install Ghost Controls-compatible hinge and roller replacement parts for residential swing gates across Fort Worth, with most jobs completed in a single visit. Typical installed pricing runs $185 to $420 depending on the hinge configuration and gate weight, and we quote the full price before any work begins. You’ll usually discover the problem the same way every Fort Worth homeowner does: the gate starts dragging on the close, scraping the driveway, or the opener labors harder than it did last spring and the gate sits a half-inch lower than it should.

Call (817) 562-7979

We’re an independent gate service company, not affiliated with Ghost Controls. What that means for you is honest guidance on whether to use OEM parts or a quality equivalent, backed by a written 90-Day Done Right Promise on every install we perform.

Which Ghost Controls Models This Applies To

Ghost Controls builds three main residential swing-gate opener families: the AXPB single-arm kit, the AXDP dual-arm system, and the newer R series with the TSS1 torque-sensing module. The hinge and roller hardware on your gate doesn’t actually belong to Ghost Controls, which is the first thing to understand. Ghost Controls makes the opener arm and control board. The hinges, gate wheels, and the roller that carries the gate’s outer edge are installed by whoever hung the gate originally, often years before the opener went on.

That’s the compatibility gotcha most homeowners hit: there is no Ghost Controls part number for a replacement hinge. What matters is the gate’s weight, leaf width, and post gap, not the opener model. A Ghost Controls AXPB pulling a 12-foot ornamental steel leaf in Arlington Heights needs a heavier barrel hinge and a different roller than the same opener swinging a 9-foot aluminum gate in Ryan Place. If you can find the gate fabricator’s name on the post or the hinge plate, that helps us match the original geometry. If not, we measure the leaf, weigh it, and select the hinge and roller that fit and carry the load correctly. We stock OEM-spec and heavy-duty aftermarket equivalents on the truck, so the correct part comes with us on the first visit.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• The gate scrapes or drags at the far end. The roller is worn flat or the hinge barrel has sagged, dropping the leaf low enough to catch the driveway. In Fort Worth’s clay soil, concrete shifts seasonally and gates that cleared in January will scrape by August.
• The opener grinds but the gate moves slowly. A failed roller adds drag the motor keeps fighting, which shortens arm life on the Ghost Controls opener. The motor is pulling against metal-on-concrete friction, not rolling resistance.
• You can lift the gate leaf an inch or more by hand. The hinge pin or barrel is worn egg-shaped, meaning the gate is no longer carried square. Every time it swings, it works the hinge further out of round.
• The gate leans toward the latch post when closed. The top hinge has worn while the bottom has not, or vice versa, throwing the leaf out of plumb. The opener now has to push uphill against its own weight.
• Squealing or a rhythmic thump while the gate moves. Squeal is the roller bearing or hinge pin dry and grinding. The thump is usually a flat-spotted roller hitting the same wear point every revolution. Both are warnings, not failures, but they become failures quickly in Texas heat.

Replacement Cost & What’s Included

In Fort Worth, a Ghost Controls-compatible hinge and roller replacement typically lands between $185 and $420 installed. A simple bottom roller swap on a lighter aluminum gate runs on the low end. A full hinge set plus roller replacement on a heavy ornamental steel leaf, where we have to unbolt the leaf, support it, and reset it square, runs toward the top. Gates with two leaves double the work, and if the post has shifted, that gets corrected before the new hardware goes on, because a new hinge on a leaning post is a hinge condemned to fail again.

Every quote includes the parts, the labor, the adjustment, and a function test on the opener once the gate swings true. We settle the price before a single bolt is turned. The work is covered by our 90-Day Done Right Promise, in writing, no paperwork and no arguing.

DIY or Call Us?

There’s a piece of this you can handle safely, and a piece you should not touch. You can lift the gate leaf by hand to feel for slop, watch the roller as the gate moves to confirm the flat spot, and note whether the scrape happens only when the gate is hot. That’s useful information to have when you call. What you should not do is attempt to unbolt the hinge or support a heavy leaf with a floor jack and scrap wood. A 300 to 400 pound steel gate leaning off its hinge post has injured more Fort Worth do-it-yourselfers than any other gate repair. The leaf has to come off its load path with proper support at two points and reset within about an eighth of an inch, or the Ghost Controls opener will bind and wear itself out even with brand new hardware. If you want to diagnose it yourself over the phone, call us at (817) 562-7979 and talk it through. If the gate’s already on the ground or the hinge is cracked through, that is a call-it-in-now situation.

FAQs