Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Everman
Gate motor and opener repair in Everman usually comes down to one of three things: a stripped gear, a misaligned photocell, or a post that shifted in the clay. A proper fix costs $180 to $260 for common repairs, while a new slide motor installation typically runs $1,400 to $2,800 depending on the gate width and power run. We’re Gate Motor & Opener specialists, and we answer the phone live at (817) 562-7979 whenever your gate quits. Most Everman calls get a technician out the same day for repairs.
We’ve worked gates on Enon Avenue, around Everman High School, and throughout the neighborhoods off W Camp Wisdom Road and Forest Hill Drive. We know what the soil does to a gate operator out here. That local knowledge means we’re not guessing at the fix when we pull up your driveway.
Why Ironworks Gate Co. Is Everman’s Preferred Gate Motor & Opener Company
Ironworks Gate Co. has been doing this work for over 42 years, founded in 1984 by people who still answer the phone. Victor Salinas leads our crews, and the standard he set is simple: a square deal, upfront pricing settled before a single bolt is turned, and a written 90-Day Done Right Promise on every job. If it’s not right, we come back and make it right. No paperwork, no arguing.
Everman is a small town, and word travels fast. The homeowners who call us out here tend to have lived in the same house for twenty or thirty years. They remember the last contractor who left a gate half-working. That’s why most of our Everman work comes from neighbors telling neighbors. We show up in a marked truck, background-checked and uniformed, and we treat your property the way we’d treat our own mother’s.
Live phone support runs 24 hours a day, 7 days a week. Not a voicemail tree. Not an answering service. A real person picks up at (817) 562-7979, any hour, including storm nights when a gate is stuck open and the dogs are out.
Our Gate Motor & Opener Services in Everman
Motor Installation in Everman
A proper gate motor installation in Everman starts underground, not at the motor. We check the gate post footings for settlement before mounting anything. Clay soil out here heaves with the seasons, and a motor bolted to a drifting post will bind, strip gears, and fail early. We handle the full scope: concrete work, power run, safety edges, photocells, and reversal testing. A new installation in Everman takes one to two days and comes with a written quote before we start. No same-day promises on installation. That’s measured work, ordered parts, and scheduled crew time. Call (817) 562-7979 for a free measure and a firm number.
Motor Repair in Everman
Most Everman motor repairs are same-day. We carry common gears, limit switches, photocells, and control boards on the trucks, so a stripped Viking gear or a BFT board that’s gone dark doesn’t mean waiting a week for parts. The most frequent repair we see in Everman is a gear stripped from post binding, almost always traceable to clay settlement under the gate hinge post. We fix the operator and correct the binding source so you’re not calling us back in six months. Repair pricing in Everman runs $180 to $340 for most jobs.
Linear Motor Service in Everman
Linear arm motors are common on older Everman swing gates, particularly the 1990s and early 2000s builds along the streets off Forest Hill Drive. We rebuild and replace Linear operators, re-set the limit cams, and re-run the obstruction sensing so the gate reverses properly if a grandchild or a delivery driver is in the path. A Linear motor replacement in Everman typically falls between $1,200 and $2,200 installed, depending on gate size and whether the original mounting plate can be reused.
Slide Motor Service in Everman
Slide gates are common on the larger lots south of Everman High School and along the semi-rural properties off Old Cleburne Road. Slide operators in Everman take a beating from two directions: the motor works harder than it should when the rack and pinion bind, and the rollers clog with a mix of dried clay and fine grit. We install, repair, and convert slide motor systems, including chain-to-rack conversions. If the gate was originally chain-driven and the chain is sagging or jumping, we can convert it to a rack-and-pinion system with a new operator.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Everman
We’re factory-trained and equipped on nine gate automation brands, including Viking, Ghost Controls, and DoorKing. When a DoorKing board fails or a Ghost Controls actuator loses its range, we know the wiring and the programming before we lift the cover. We keep a rolling stock of common parts for Everman jobs: limit switches, photocells, control boards, and remote receivers. That means most repairs finish on the first visit instead of burning a second truck roll. Whether it’s a Viking operator on a new build or a tired Ghost Controls opener that’s been in service for fifteen years, the fix is coming from someone who knows the unit.
Common Gate Motor & Opener Problems We See in Everman Homes
- Stripped gears from post settlement. Everman’s expansive clay absorbs winter moisture and dries in July and August. The ground moves, the hinge post tilts a quarter inch, and the gate binds against the operator. The motor keeps pushing until the gear gives out. We re-set the footing and true the post before installing the new motor, otherwise the same failure comes back.
- Photocell false reversals after rain. When the soil swells after a good rain, the gate frame flexes and the safety beam aim drifts. The gate starts closing, sees a false obstruction, and reverses for no visible reason. This is the most common “haunted gate” call we get in Everman.
- Battery backup failures after spring storms. Everman’s severe storm season brings wind that drops trees on rural lines and knocks power out for hours or days. A solar or battery backup gate opener that loses its charge leaves the gate dead. We size and install backup batteries rated for the gate’s duty cycle and the property’s exposure.
- Limit switches creeping out of adjustment. As the post shifts through the season, the gate’s open and closed positions drift. A gate that once closed flush against the stop now stops two inches shy, or over-travels and grinds. Re-setting the limits is part of every repair we do, but when the post is the culprit, the real fix is post work, not just a limit adjustment.
Pricing for Gate Motor & Opener in Everman, TX
Here’s what honest numbers look like in Everman, straight from our invoices.
- Motor repair (gear replacement, limit switch, photocell realignment): $180 to $340
- Linear motor replacement: $1,200 to $2,200 installed
- Slide motor replacement: $1,400 to $2,800 installed, more for heavy estate gates
- Full motor installation with power run and safety edges: $1,800 to $3,500 depending on gate weight, length, and distance to the panel
- Battery backup addition: $350 to $800 installed depending on the system
- Seasonal tune-up: $89, includes post check, gear lubrication, limit re-set, and safety reversal test
Every price is quoted and agreed in writing before any work starts. You will not get a call saying “it ended up being more.” You get the number, you approve it, we do the job. Estimates are free. Call (817) 562-7979 and we’ll send a technician out to measure and quote.
We Also Serve Cities Near Everman
Our Everman crews work the full corridor around the city, and we run regular routes into Fort Worth, Aledo, Azle, and Benbrook. If you’re just outside Everman proper, call and ask. If we’re not already in your neighborhood, we’ll schedule a run and still beat anyone who has to drive in from across the metro.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Everman
After heavy rain, Everman’s clay soil swells and shifts the gate post, which flexes the gate frame and knocks the safety photocells out of alignment. The opener sees the misaligned beam as an obstruction and reverses. The fix is a post check and a photocell realignment, not a new motor. Our technicians do this on a single visit. Call (817) 562-7979 and we’ll get you squared away.
Yes, and it’s the correct repair when the soil has moved. We dig out the old footing, set the post in concrete with proper depth for Everman’s clay, and true it so the gate hangs straight. Then we mount the new operator on a stable post. Skipping the post work means the new motor inherits the same bind and fails the same way. Our quote always includes any post work the job needs, priced up front.
Yes, and we do it regularly on the older chain-drive gates around Everman’s semi-rural lots. We remove the sagging chain and sprockets, install a steel rack along the gate, and mount a new slide operator matched to the gate’s weight and length. The result is a gate that runs straighter, quieter, and stops exactly where it’s supposed to. Conversions in Everman typically run $1,800 to $3,200 depending on gate size and the condition of the existing posts and rollers. Estimates are free.
For most Everman gates, we recommend a sealed lead-acid battery backup sized at 7 to 12 amp-hours for swing gates and 12 to 18 amp-hours for slide gates. The exact size depends on your gate’s weight and how often it cycles, plus how long your street is typically down after a storm. We install the backup, wire it to the operator, and test it under load. A battery backup install in Everman runs $350 to $800, and we’ll show you how to check the battery health yourself. Call (817) 562-7979 to schedule a look at your system.
A standard swing gate motor installation takes one day for the mechanical work and wiring, with a second half-day if we’re running power from the house panel. Slide gate installations take one to two days depending on the rack length and concrete work. We never promise same-day installation. That’s scheduled, measured work with a written price agreed before we start. To get a real timeline and a firm quote for your gate, call (817) 562-7979.
If your gate is acting up in Everman, start with a phone call. A live person answers at (817) 562-7979, day or night. We’ll talk through what you’re seeing, tell you what it probably costs, and get a technician out on a schedule that works. Free estimates, upfront pricing, and a written 90-Day Done Right Promise on every job.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Everman gate automation needs with crews based in the Dallas-Fort Worth area.