Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Everman
A sagging gate in Everman is usually one of three things: a worn hinge, a failed post, or a broken weld at the rail. Our crews see all three every week between Enon Avenue and the older streets off Trammell. We quote the repair honestly, get it done in one visit when the gate can be salvaged, and we stand behind the work with a written 90-Day Done Right Promise. Call (817) 562-7979 and a live person picks up, day or night.
Why Ironworks Gate Co. Is Everman’s Preferred Gate Parts & Welding Company
Everman is a tight-knit town where word travels fast. When one swing gate fails on a block, neighbors notice, and they talk. That is why our Everman work tends to come in clusters: a hail event rolls through, three gates on the same street lose top hinge screws, and we end up repairing all three within a couple weeks. Being local to the metro means our Everman response is measured in hours, not days, when a gate is stuck open or dragging.
We are not the cheapest bid in Everman, and we will not pretend to be. We are the firm that replaces the hinge once, set the post footing deep enough that the next wind event does not loosen it, and gives you a written guarantee on the whole repair. Victor Salinas built this company on that standard over 42 years ago, and Everman homeowners have come to expect it.
Every technician who works in Everman is background-checked and uniformed. We treat your driveway the way we would treat our own mother’s. The price is set before we turn a single bolt, and if something is not right, we come back and make it right. No paperwork chase, no arguing.
Our Gate Parts & Welding Services in Everman
Hinge Replacement
Wind-driven swing gates in Everman are hard on top hinges. The repeated pressure pulls screws loose from the post, the latch drifts out of alignment, and the gate starts scraping. We carry adjustable barrel hinges, heavy strap hinges, and weld-on hinge kits for steel posts, so the replacement usually happens same day. On a wooden post that has stripped out, we sister a steel plate behind the hinge or switch to a through-bolt with a backing plate.
Post Replacement
Everman sits on clay soil that expands and contracts through wet and dry cycles. Shallow post footings heave, which shifts the gate enough to bind the rack and pinion on a slide gate or drop a swing gate’s latch below the strike plate. A proper post replacement here means a new footing 30 inches deep minimum, set in concrete, with the old post torch-cut at the base and removed clean. We install the new post, weld on fresh hinge mounts, and re-hang the panel to clear properly.
Rail Repair
The top rail on a steel tube gate carries tension that wind worsens over time. A hairline crack at a welded joint becomes a full split, and the gate starts to flex when it moves. We grind the crack back to sound metal, weld it with full penetration, and add a gusset plate when the design allows. For ornamental gates off Everman Parkway with decorative scrollwork, we match the weld profile so the repair does not look like a patch.
Custom Welding
Sometimes a gate is worth saving precisely because it was built to match a fence that no one makes anymore. We weld custom steel frames, build replacement panels to match existing picket spacing, and fabricate mounting brackets for odd post sizes. If a homeowner on Nolan Lane wants a cane bolt guide or a drop rod re-anchored, that is a 40-minute job on a day we are already in Everman.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Everman
Our Gate Parts & Welding crew works on the mechanical side of every gate brand common in Everman driveways. On the automation side, we are trained and equipped on nine opener brands, including Ghost Controls, DoorKing, and Mighty Mule. When a weld or hinge repair touches a motorized gate, we know how the opener tolerances interact with the repair. A slide gate that binds on the rack will burn out a DoorKing motor faster than most people realize, and we address that during the job rather than leaving you with the next failure.
Common Gate Parts & Welding Problems We See in Everman Homes
- Wind-pulled top hinge screws. Everman’s position in the path of southern plains storms means swing gates get hammered from the side. Top hinge screws back out of wooden posts, the latch misses the strike plate, and the gate sags on its barrel hinges. We re-anchor with through-bolts and backing plates when the post allows.
- Hail-shorted loop detector wires. Slide gates on Everman properties with vehicle loop detectors fail after a hailstorm cracks the wire’s insulation at grade. The operator refuses to close because it thinks a car is on the loop. We trace the short, splice in a sealed section, and re-test reversal pressure.
- Heaving post footings. Everman’s clay soil moves through wet and dry seasons, and original post footings from older installs are often too shallow. The post shifts, the gate binds, and the rack and pinion grinds. Our fix is a new footing set 30 inches deep and re-aligned to the operator.
- Cracked rail welds on steel tube gates. The repetitive flex from wind and daily cycles eventually cracks the welded joint between the top rail and the picket line. It starts as a hairline and grows unpredictable. We grind, weld, and plate the joint so the gate stiffens back up.
Pricing for Gate Parts & Welding in Everman, TX
Hinge replacement on a standard swing gate in Everman typically runs $180-$340, including new hinges, hardware, and alignment. A post replacement with a 30-inch footing and re-hang runs $450-$900, depending on post size and whether the operator needs re-tuning. Rail crack repair and gusset plating runs $150-$400 per joint. Custom welding work, like a full gate frame to match an existing fence, runs $800-$2,400 depending on the dimensions and steel schedule.
We quote the price before any work starts, and the written price is what you pay. Estimates are free. Victor Salinas has never believed in showing up with a bill that surprises the homeowner. Call (817) 562-7979 and we will give you a square number over the phone or schedule a measure in Everman.
We Also Serve Cities Near Everman
Our crews serve Everman and the surrounding communities, including Fort Worth, Aledo, Azle, and Benbrook. If you are just outside the Everman city line, call us anyway: the scheduling runs the same, and the pricing does not change based on which side of a boundary you live on.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Everman
It depends on where the failure is. If the weld at the rail is cracked but the post is still plumb, we can weld the panel back to sound metal in a single visit. If the post is leaning or the footing has heaved, welding the panel alone will not fix the geometry: the gate will still drag. We will tell you honestly which one you have. Call (817) 562-7979 and we will tell you over the phone before we ever schedule the truck.
Yes. We carry adjustable barrel hinges and heavy strap hinges that fit a 3-inch steel post, and we have weld-on hinge mounts for exactly that configuration. If you are in Everman and the gate is dragging, the hinge replacement is usually a same-day job. (817) 562-7979 is the number.
A proper post replacement includes removing the old post at grade, augering a new hole 30 inches deep minimum, setting the new post in concrete, and re-aligning the rack and pinion to the operator so the gate does not bind. We also re-test the operator’s reversal pressure after the re-hang, because the gate’s travel path has changed. Our written quote covers all of it before work starts.
Yes. We fabricate custom steel frames and can match the picket spacing and top profile of an existing Everman fence. The frame is welded in our shop, then fitted and hung on site. This is measured, fabricated work, so we schedule it rather than promising same-day. A free measure is the first step: call (817) 562-7979.
On most Everman gates, that clicking is the capacitor or the limit switch trying to engage while the motor is bound up. The usual cause is mechanical: a hinge or post has failed and the gate is dragging, so the operator cannot overcome the added friction. We check the mechanical path first, then the opener internals. If it is a Ghost Controls or Mighty Mule unit, we carry the common replacement parts on the truck.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Everman and the surrounding metro.