Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Azle
Gate hinge replacement in Azle typically runs $240-$480 per hinge set, and most jobs are completed the same day we arrive. Post replacement runs higher, usually $600-$1,200 depending on footing depth and whether we’re cutting through caliche or wet clay. If you’re on a ranchette off FM 730 or FM 199 with a sagging pipe-rail gate or a snapped ornamental iron weld, call us at (817) 562-7979 for a straight answer and a free estimate. We know exactly what Azle’s clay does to gate hardware, and we plan our repairs around it.
Ironworks Gate Co. has been welding and repairing gates for over 42 years. We work on the older gates Azle homeowners actually have: 1970s ornamental iron driveway gates, pipe-rail ranch gates on wood posts, and swing operators that predate modern safety codes. Victor Salinas leads our crew, and every job carries the 90-Day Done Right Promise in writing.
Why Ironworks Gate Co. Is Azle’s Preferred Gate Parts & Welding Company
Azle is not a dense suburb, and the gate work here is not suburban gate work. We get called to properties off Ten Mile Bridge Road, Briar-Reno Road, and Sandy Beach Road where the driveway is 200 feet of gravel and the gate has been swinging on the same hinges since Reagan’s first term. Our technicians know what that means: deeper post footings, heavier hinge barrels, and solar operators that have to survive a North Texas ice storm without grid power. The company that re-hung a gate in a subdivision off Boat Club Road may never have touched a 16-foot pipe-rail gate hung on an old telephone-pole post.
We coordinate dispatch for Azle from our Dallas-Fort Worth metro office, and crews serve Azle locally. A live person answers the phone 24 hours a day, 7 days a week. Not a voicemail, not an answering service. If your gate is down at 9:30 on a Sunday night with a horse on the wrong side of the fence line, someone picks up.
Victor Salinas has been running gate crews long enough to know when a weld will hold and when it won’t. He’s the guy who tells a customer the honest truth: that hinge can be re-welded and will last five more years, or that post is too far gone and needs to come out. That candor is why Azle homeowners keep our number by the garage door. Our background-checked, uniformed technicians work by a code we call K.E.Y.S.: Krafted right, Every time, Your home first, Standing behind it. The 400th job gets the same care as the first.
Our Gate Parts & Welding Services in Azle
Our Gate Parts & Welding work in Azle spans the full range, but three services dominate the call volume out here. Here’s what we actually do most weeks.
Hinge Replacement
A worn hinge barrel on a 300-pound gate does more than squeak. It grinds the post, throws the gate out of level, and eventually snaps the hinge plate clean off. We replace hinges with heavier-gauge steel than what was originally hung, then re-align the operator so the limit switch isn’t fighting a gate that no longer swings true. On pipe-rail ranch gates off FM 199, we regularly see hinge barrels worn completely through from forty years of gravel dust and no grease. New hinge assemblies, properly bedded, usually run $240-$480 per set in Azle.
Post Replacement
On Azle’s shrink-swell clay, posts are the failure point. A gate hinge post can heave 2-4 inches out of plumb between a wet spring and an August drought. Welding a new hinge onto a post that’s still moving fixes the gate for one season at best. When we re-set posts, we dig the footing deep, set the post in concrete below the active clay line, and brace it plumb while the concrete cures under load. Nobody likes a gate that whacks the ground every time the soil dries out. Post replacement in Azle runs $600-$1,200, more if we’re cutting roots around post oaks or chiseling through caliche ledge.
Rail Repair
Older ornamental iron gates in 1970s ranch-style neighborhoods along Jacksboro Highway take a beating. Picket welds crack, bottom rails rust from the inside, and the diagonal brace stretches until the gate droops on the latch side. We cut out the bad rail, weld in new square tube or solid bar stock to match, and re-square the gate before it goes back on its hinges. We grind every weld smooth enough to paint, because a bumpy bead collects water and rusts out again in five years. Most rail repairs in Azle land between $180 and $400 depending on how much rail we’re replacing.
Custom Welding
Sometimes the part doesn’t exist anymore. A 1978 gate with a cracked speakeasy frame, a custom ranch sign bracket, a solar panel mount that needs re-engineering for an oak that grew taller. We weld to match the metal that’s already there, not whatever’s quickest from the truck. Our shop can fabricate hinge plates, receiver brackets, and sensor mounts that never came out of a catalog. Custom welding in Azle starts around $150 for a straightforward bracket and goes up from there based on steel and shop time.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Azle
We’re trained and equipped on nine gate-automation brands, including Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters out here because Azle’s ranchettes run a mix of whatever opener was on sale at the farm store in 2009 next to a DoorKing slide operator installed by the builder. We diagnose the actual brand and model on the gate, carry common control boards and limit switch assemblies in the truck, and we order less common parts the same day. We also service the low-voltage side: solar controllers, battery banks, loop detectors, and keypads. One technician, one visit, whatever’s on the post.
Common Gate Parts & Welding Problems We See in Azle Homes
- Heaving hinge posts on clay. Azle sits on shrink-swell Blackland and red clay that cracks hard in drought and swells after rain. A post that moved 3 inches this spring no longer lines up with the hinge, and the gate binds or the weld tears. Re-setting the post is the fix, not more welding.
- Solar operators that die in ice storms. On long FM-road drives, trenching power is cost-prohibitive. Solar-charged battery banks keep the gate alive until an ice storm shades the panel, freezes the battery, and the old control board doesn’t load-shed. We test battery capacity, panel output, and controller logic, not just the motor.
- Pre-UL 325 gates with no entrapment protection. 1970s ornamental iron driveway gates were hung before modern entrapment rules existed. Adding photo-eyes and edge sensors means welding new brackets onto twisted pickets. We do that here, often on gates that haven’t been touched since they were hung.
- Rust-through on bottom rails and hinge barrels. Azle’s red clay holds moisture against steel, and gates that scrape through wet grass every spring rust from the bottom up. We fabricate replacement rails and hinge barrels in heavier gauge than the original.
Pricing for Gate Parts & Welding in Azle, TX
| Service | Typical Azle Price Range |
|---|---|
| Hinge replacement (per set) | $240 - $480 |
| Post replacement (single gate post) | $600 - $1,200 |
| Rail repair / straightening | $180 - $400 |
| Custom bracket / mount fabrication | $150 - $500 |
| Full re-hang with operator re-alignment | $450 - $900 |
Every price is quoted and agreed before any work starts. No surprises on the bill, ever. We also offer $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% discount for seniors and veterans. Call (817) 562-7979 and we’ll give you a real number for your gate, not a range pulled from a website.
We Also Serve Cities Near Azle
Our Gate Parts & Welding in Azle crews also cover homeowners just outside the city line. We run regular routes through Haslet, Aledo, Keller, and Haltom City. If you’re on a ranchette in any of those communities with a gate problem, the same crew and the same 90-Day Done Right Promise applies. One call covers the whole area.
Serving Azle, TX - Our Local Coverage Area
We’re based in the Azle area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Azle
No. If the post is moving with the clay, welding a new hinge onto a moving post fixes the gate for one season at best. The post itself needs to be dug out, the footing deepened below the active clay line, and the post set in concrete so it stops heaving. Then the hinge gets welded and the whole gate re-hung plumb. We quote the post reset and the hinge replacement together, so the price you hear is the price you pay. Call (817) 562-7979 for a free estimate.
Yes. We retrofit older gates with photo-eyes, edge sensors, and modern control boards that meet current UL 325 entrapment standards. On 1980s ornamental iron, the sensor brackets usually need to be custom-welded onto the pickets because factory brackets don’t fit. Our shop fabricates those mounts on-site. The work is done the same day, and it carries the 90-Day Done Right Promise in writing.
Not usually. Most of the time the operator’s fine, but the battery bank has lost capacity, the solar panel is shaded by a post oak or covered in ice, or the old control board isn’t load-shedding when voltage drops. We test the panel output, battery capacity under load, and controller logic before we ever replace a motor. Replacing a battery bank runs $150-$350. Replacing the operator is a last resort. Call (817) 562-7979 and we’ll diagnose it properly.
On-site. We bring a portable welder, grinders, and steel stock to every Azle job. We weld the crack, reinforce the weak section with a gusset where needed, grind it smooth, and leave it ready for paint. If the gate is too far gone, we’ll tell you straight before we weld anything, and we’ll quote the fabrication of a new gate to match. The choice is yours, and the estimate is free.
The low-voltage wiring for the keypad and loop detector almost certainly runs through the same post or under the same footing that got re-set. If the wire was nicked, crushed, or left disconnected during the concrete work, the accessories lose power or signal while the operator itself still works. We trace the wire, splice or re-pull it, and test the loop detector frequency before we leave. If it’s a different crew’s post work, we’ll still fix it and show you what actually failed.
Call Ironworks Gate Co. for Gate Parts & Welding in Azle
If your gate post is heaving on Azle clay, your solar operator is dead after an ice storm, or your 1970s ornamental iron gate cracked a weld, call (817) 562-7979. A live person answers. Victor Salinas will make sure you get a straight answer, a written price before work starts, and the 90-Day Done Right Promise after the job is finished. We serve the whole Azle area, from the ranchettes off FM 730 and FM 199 to the lake roads off Eagle Mountain Lake. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Azle with gate parts and welding expertise.